九九热免费在线观看_毛片女人毛片一级毛片毛片_欧美在线视频一区二区_在线免费看av片_精品视频9999_99视频网站

浙江睿創晟業電氣有限公司
免費會員

當前位置:浙江睿創晟業電氣有限公司>>繼電器系列>>電力繼電器>> QJ4-80QJ4-80氣體繼電器

QJ4-80氣體繼電器

參  考  價面議
具體成交價以合同協議為準

產品型號QJ4-80

品       牌

廠商性質生產商

所  在  地溫州市

更新時間:2022-01-25 14:20:22瀏覽次數:1967次

聯系我時,請告知來自 智慧城市網
同類優質產品更多>
QJ4-80氣體繼電器
QJ系列氣體繼電器,是油浸式變壓器所用的一種保護裝置,由于變壓器內部故障而使油分解產生氣體或造成油流涌動時,使氣體繼電器的接點動作,接通的控制回路,并及時發出信號或自動切除變壓器。

QJ4-80氣體繼電器

型號
 QJ3-50,QJ3-80,QJ4-50,QJ4-80,QJ4-25
產品系列   瓦斯氣體繼電器
觸點形式   常開型
額定電壓   AC380-440(V)
電流性質   交流
外形       大型
功率負載   大功率
防護特征   封閉式
直流電阻   1000(Ω)
吸合電流   5(A)
釋放電流   5(A)
線圈功率   5(W)
用途:QJ4-50型氣體繼電器是帶儲油柜的油浸式變壓器以及有載調壓開關的一種保護裝置。
      該繼電器安裝在變壓器以及有載調壓開關油箱與儲油柜之間的連接管道中.
 
技術參數:
跳閘接點動作的油流速度范圍和出廠整定值
型號        QJ-80        QJ-50         QJ-2
流速范圍0.7-1.5m/s     0.6-1.0m/s       1.0m/s
出廠整定 1.0m/s        0.8m/s            1.0m/s
 
1.繼電器管路直徑:
    QJ-25型為ф25,QJ-5O為ф50,QJ-80為ф80
2.繼電器的工作溫度:-30℃-+95℃
3.信號接點動作氣體容量:250-300cm3
4.接點額定容量:220V 0.3A,110V 0.6A(S ≥5×10 S)
5.絕緣強度:2000V/nim
6.密封性能:繼電器內充滿變壓器油,在常溫下加壓200Kpa/20min,無滲漏現象。
7.抗震能力:當振動頻率(正弘波)4-20赫茲,加速度為4g時,繼電器不誤動。(g為重力加速度)
8重量:QJ-80 11kg,QJ-50 10kg,QJ-25 6kg(供參考)


 

QJ2-40型氣體繼電器

1.   用途 The use

 

QJ2-40型氣體繼電器主要用于保護各種類型的油浸式全密封變壓器的安全運行。必要時將變壓器從電網中切除。

 

A gas relay in QJ2-40 is mainly used for protection of safe running of various types of oil-immersed fully sealed transformer. If necessary, the transformer will be cut off from the power grid.

 

2.   型號及其含義 The model and its meanings

 

本產品的型號及其所代表的意義如下:

 

The model and its meanings of the product are following:

 

 

 

 

3.   氣體繼電器的結構及其工作原理 The structure and the work principle of the gas relay

 

3.1 氣體繼電器外部結構如圖所示:The outer structure of the gas relay is following:

 

內部由浮子及兩個干簧接點構成,接點閉合將報警信號或切除信號通過接線端子輸出。

 

The inner is composed of float and two spring contacts and the contact closing makes alarm signal or cutting signal output by the connection terminal. 

 

3.2 氣體繼電器的工作原理 The work principle of the gas relay

 

當變壓器內部出現故障,變壓器油分解而產生氣體或溫度下降而少油,此時氣體聚集在繼電器的氣室內,迫使油面下降,浮子隨油面下降,當油面下降到一定程度時,首先報警信號接點接通,發出報警信號。若油面繼續下降,到一定程度時,切除信號接點接通,發出切除信號,將變壓器從電網中切除,從而達到保護變壓器的目的。

 

When the fault takes place inside of the transformer, the transformer oil is decomposed to produce o gas or make the temperature drop to result to less oil. At this time, the gas is gathered in the gas interior of the relay to force the oil level to drop and the float will drop with the oil level. When the oil level is dropped to a certain degree, the alarm signal contact is connected to send the alarm signal out at first. If the oil level continually drops to some degree, the cutting signal contact is connected to send the cutting signal out to cut the transformer off from the power grid to reach at the purpose of the protection of the transformers.

 

 

 

4.   主要技術參數 The main technical parameters

 

4.1 工作溫度 The work temperature:-30℃~ +90℃

 

4.2 管路通徑 The pipeline path diameter:Φ40mm

 

4.3 密封試驗壓力 The seal test pressure:0.2MPa   20min

 

4.4 接線端子對地 The earth terminal blocks:AC  2KV  1min

 

4.5 接點容量 The contact capacity: DC/AC  220V  0.3A

 

4.6 動作特性 The action characteristic:

 

當油面下降到箱蓋下35mm處,發出報警信號。

 

When oil dropped to 35mm under the cover, send an alarming signal out.

 

當油面下降到箱蓋下50mm處,發出切除信號。

 

When oil dropped to 50mm under the cover, send a cutting signal out.

 

5.   安裝尺寸 The installation size

 

 

 

QJ2-40型氣體繼電器的結構及安裝尺寸

 

The structure and the installation size of gas relay in QJ2-40

 

6.   使用及維護 The use and the maintenance

 

6.1 產品出廠前,已經過調試和密封試驗,無特殊情況下不要隨意拆卸,以免影響產品的準確度和密封性能。

 

Before the products leave the factory, they have been adjusted and test. In common case, they should not been disassembled arbitrarily, so as not to affect the accuracy and the sealing performance of the products.

 

6.2 為方便氣體繼電器進行現場檢修,其安裝位置應保證氣體繼電器芯體能從殼體中取出。

 

In order to help the repair of the gas relay in site, its installation location should ensure the core body of the gas relay to be able to be removed from the shell.

 

6.3 氣體繼電器必須安裝在變壓器油箱箱蓋上,便于收集氣體。安裝法蘭和密封墊由繼電器生產廠提。

 

The gas relay must be installed on the tank cover of the transformer to facilitate the collection of gas. The installed flanges and the seal gaskets will be provided by the relay manufacturer.

 

6.4 放氣及收集氣樣:將放氣閥上的防塵蓋擰下,旋動內部的小六角氣閥即可放氣。若在放氣嘴上接一內徑Φ6的膠管,即可收集氣樣。

 

The Deflation and collecting gas samples: Turn the dust cover on the releasing valve off and turning the small inner hex valve can release gas. If connect a hose with Φ6 diameter to the releasing nozzle, it can collect the gas sample. 

 

6.5 電氣接線:1、2端子接報警信號,3、4端子接切除信號(見A向圖)。

 

The electrical wiring:Terminal 1, 2 for alarming signals; Terminal 3, 4 for cutting signals (see diagram A)

 

6.6 安裝時不得將浮子外保護罩去掉.

 

When installation, the outer protection cover of the float can not be removed.

 

7.   投運前測試 The test before put into operation  

 

投入運行前,利用氣體繼電器頂蓋上的探針可進行動作特性的測試。先擰下探針頂上的防塵蓋,緩慢按下探針,將依次發出報警信號和切除信號。如不能發出信號,請檢查接線是否正確,若確認接線正確仍不能發出信號,請立即與我公司,我公司將迅速予以解決。

 

Before put into operation, use the probe on the cap of the gas relay can carry out the test of the action characteristic. At first, turn off the duct cap on the probe and press the probe down slowly, it will send alarm signals and cutting signals out I order. If it can not send a signal out, check if the wiring is correct. If The wiring is confirmed to correct and it still can not send the signal out,  please do not hesitate to contact our company, my company will be resolved quickly.

 

 

 

 

 

QJ4-25

 

技術數據
用途QJ型氣體繼電器是全密封變壓器所用的一種保護裝置,氣體繼電器以下簡稱繼電器,安裝在全密封變壓器油箱上,當變壓器內部發生故障而使變壓器而使油分解產生氣體或油面下架時,氣體繼電器的接點動作,以接通的控制回路,并及時發出信號或自動切除變壓器電源。
技術參數

1.流速范圍:1.0m/s 出廠整定:1.0m/s

2.接點額定容量:220V 0.3A,110V 0.6(S≯5×10-3)

3.絕緣強度:2000V/min

4.密封性能:繼電器內充滿變壓器油,在常溫下加壓200Kpa/20min

  
安裝尺寸

D Φ25

D1 Φ85

do Φ14

A 100

H ≤200

B   /

L 200

 
 

QJ4-80氣體繼電器   QJ4-80氣體繼電器 

會員登錄

×

請輸入賬號

請輸入密碼

=

請輸驗證碼

收藏該商鋪

X
該信息已收藏!
標簽:
保存成功

(空格分隔,最多3個,單個標簽最多10個字符)

常用:

提示

X
您的留言已提交成功!我們將在第一時間回復您~
在線留言
主站蜘蛛池模板: 一级毛片免费高清 | 午夜精品久久久久久久 | 国产资源在线免费观看 | 在线播放视频一区 | 九九九久久久精品 | 国产性av网址大全 | 好吊妞视频788gao在线观看 | 亚洲欧美日本国产 | 色花堂国产精品第一页 | 色琪琪丁香婷婷综合久久 | 久久久婷婷白浆水 | 99久久一区二区三区 | 免费在线播放黄色 | 久久久国产99 | 婷婷五月综合国产激情 | 欧美精品videos另类 | 日韩一区二区三区在线免费观看 | 国内极品少妇1000激情啪啪千 | 成人禁污污啪啪入口 | 日本一区二区免费在线 | 一级在线观看 | 国精品久久久久久久久久久58 | 亚洲精品久久区二区三区蜜桃臀 | 国产综合人综合 | 黄色一级小视频 | 桃色视频在线播放 | 999zyz玖玖资源站一区二区 | 女人精69xxx免费网站 | 欧美精品粉嫩高潮一区二区 | 岛国免费视频资源 | 国产h视频| 国产大片在线观看 | 精品国产乱码久久久久久天美 | 亚洲精品91久久久久久 | 林深见鹿40集高清免费观看 | 一本色道久久综合亚洲91 | 麻豆国产在线 | 免费特级黄毛片 | 久久成人毛片 | 欧美αv日韩αv另类综合 | 斗破苍穹免费看 |